RePallet Co.Denver · Circular by design
Get a quote

Standards & compliance

Four racking failures and the warning signs they all showed

Request pricing

Everything marked with a star is required. The rest helps us quote faster.

Free to request
A working address, so a partner supplier can send your quote.
US or Canadian number.
Two-letter code such as CO, or the full name.
US ZIP or Canadian postal code.
Whole numbers only.
No phone tag — requests go to partner suppliers in our network. Fields marked * are required. See our privacy policy.

When a load comes off a rack beam, the first question is usually whether the pallet was at fault. Sometimes it was. The pattern across these incidents is boringly consistent.

The four scenarios below are composites of the kinds of racking incidents described across the warehousing and pallet industries. They are illustrative, not accounts of specific sites, and they are written up because the pattern across them is so consistent.

Illustrative scenarios. These are generic examples to show mechanisms. Nothing here is engineering advice for your installation.

Scenario one: Grade B on a beam

A heavy pallet of tinned goods is racked on an unsupported span. The pallet sags, the load shifts toward the aisle, and the front edge comes off the beam.

The pallet has a companion stringer on the outer member. A companion stringer restores a load path but it changes it — the repaired member is stiffer at the repair and more flexible either side of it, and on an unsupported span the deflection is not symmetric. It was bought as Grade B, correctly labelled, and racked by somebody who did not know that Grade B should not be racked.

What would prevent it: marking. A site running both grades needs a visual distinction between them.

Scenario two: overhang

A 48" x 40" pallet carries a load that overhangs the long sides. The overhang removes the load from above the perimeter deck boards, which is where much of the bending stress is carried, and concentrates it inboard. Deck boards split, the load settles, and a carton falls.

The pallet is Grade A and in good condition. It fails because it is being asked to carry the load in the one place it is least able to.

What would prevent it: a larger footprint, or a plywood cap to spread the load back out to the perimeter. Overhang often appears when a product changes case size and nobody revisits the pallet.

Scenario three: moisture

Pallets stored in an unheated outbuilding through a wet spring are then racked at a normal load. Damp wood loses a meaningful fraction of its bending strength relative to the same wood dry, and is considerably heavier at the same time. Pallets sag enough to contact the one below; one drops a corner.

What would prevent it: not racking damp pallets. This is easy to say and genuinely difficult to enforce, because nobody in a receiving bay has a pin meter.

Scenario four: not the pallet

A collapse blamed on a pallet turns out to be a beam that was struck by a forklift, bent out of true, and never reported. The pallet did exactly what it should have done. The rack did not.

In a case like this, the right fix is a rack inspection process, not a pallet specification change.

The pattern

Four scenarios, one shape.
ScenarioRoot causeVisible beforehand?Fix
Grade B on a beamWrong grade specified for rackingYes — the repair is obviousMark grades; write a rule
OverhangLoad changed, pallet did notYes — overhang is visibleBigger footprint or spreader
MoistureDamp storageYes — the wood is visibly darkDry storage; reject wet units
Bent beamUnreported forklift strikeYes — a bent beam is visibleRack inspection routine

All four are visible in advance. None requires a measurement, a calculation or an engineer. Somebody looking at the rack face with the right four things in mind would catch every one of them.

The four things

  • Is this pallet the right grade for a beam? Original stringers, no companion, no plugs. If in doubt, floor it.
  • Does the load overhang? Any overhang on a racked pallet is a problem, not a tolerance.
  • Is the wood dark and heavy? Damp pallets should not go up.
  • Is the beam straight? Sight down it. A bent beam is usually visible to the naked eye from the aisle.

None of that replaces a proper racking inspection regime, and nothing in this article is engineering advice for your installation. But it is what to look at first, and it is what to teach a receiving team to look at. When you order pallets for racking, say so on your quote request so the partner supplier quotes the right grade.

#safety#racking#inspection

RePallet Co. Editorial

Editorial team

These guides are written by the team behind RePallet Co., a referral service that connects businesses across Denver and the Colorado Front Range with partner pallet suppliers in its network. We do not run a yard ourselves; we pass quote requests to partners who do, and we write up what buyers and sellers of pallets generally need to know.

Let's keep your pallets in the loop

Whether you have 40 broken cores behind the dock or need 4,000 Grade A pallets a month, the conversation starts the same way.